ViewEra Computer Monitor V141 User Manual

14TFT-LCD MONITOR  
V141 Series  
USERS MANUAL  
www.viewera.com  
Rev 1.0  
1
 
1. Introduction  
Product Description  
Congratulations on your purchase of the ViewEra V141 series LCD  
monitor. It incorporates high quality display into a small light-weighted  
module. It has power-saving capabilities and emits no radiation. You will  
certainly benefit from this monitor in lots of ways; to name some of them:  
comfort, safety, space-saving and environmental protection.  
This LCD monitor incorporates 14color active matrix  
thin-film-transistor (TFT) liquid crystal display to provide superior display  
performance. Its maximum resolution of XGA 1024 x 768 is ideal for  
displaying complex graphics and high definition images. Its other outstanding  
capabilities include audio system and OSD (On Screen Display) controls.  
Package Contents  
Included with your LCD monitor as following items   
14TFT LCD monitor  
15 pin D-sub VGA signal cable  
Audio cable  
AC power cord  
AC/DC Adaptor  
Users manual  
Product Features  
High brightness, high contrast, wide viewing angle TFT LCD  
display supports resolution up to XGA 1024 × 768. @ 60Hz.  
Compatible with VESA standards.  
Built-in speakers with volume control.  
Power management system conforms to VESA DPMS standard.  
Advanced OSD control for picture quality adjustment.  
Slim bezel design.  
3
 
Screen Cleaning Techniques  
1. Gently clean the screen with a clean camel hair lens brush, or a soft, clean,  
lint-free cloth, to remove dust and other particles that can scratch the  
screen.  
2. Do not apply pressure to the screen surface when wiping it clean.  
3. Do not pour or spray any liquid directly onto the screen or casing. Chemical  
cleaners have been reported to damage the screen or case of the LCD  
monitor.  
Additional  
Read all of these instructions and save them for later use.  
Follow all warnings and instructions on the product.  
1. Product  
Do not block the vent holes in the case.  
Do not insert sharp objects or spill liquid into the LCD monitor  
through cabinet slots. They may cause accident fire, electric shock  
or failure.  
Disconnect the power plug from the AC outlet if you will not use it  
for an extended period of time.  
Do not attempt to service this product yourself, as opening or  
removing covers may expose you to dangerous voltage points or  
other risks.  
Do not touch the screen directly with your fingers. You may  
damage the screen, and oil from your skin is difficult to remove.  
Do not apply pressure to screen. The LCD panel is very delicate.  
2. Power  
Use the type of power indicated on label.  
3. Plugs  
Do not remove any of the prongs of the monitors three-pronged  
power plug.  
Disconnect the power plug from the AC outlet under following  
conditions:  
If you will not use it for an extended period time.  
When the power cord or plug is damaged or frayed.  
4
 
If the product does not operate normally when the operating  
instructions are followed. Adjust only those controls that are  
covered by the operating instructions. Improper adjustment of  
other controls may result in damage and will often require  
extensive work by a qualified technician.  
If the product exhibits a distinct change in performance,  
service may be required.  
4. Power and extension cords  
Do not allow anything to rest on the power cord.  
Do not locate this product where persons will walk over the cord.  
Use the proper power cord with correct attachment plug type. If the  
power source is 120V AC, use a power cord that has UL and C-UL  
approvals. If the power source is a 240V AC supply, use the tandem  
(T blade) type attachment plug with ground conductor power cord  
that meets the respective European countrys safety regulations,  
such as VDE for Germany.  
Do not over load wall outlets or power cords. Ensure that the total  
of all units plugged into the wall outlet does not exceed 10 amperes.  
Ensure that the total ampere ratings on all units plugged into the  
extension cord is not above the cords rating.  
If the power supply cord, which came with your monitor, is to be  
connected to the PC instead of the wall outlet, Use an UL/TUV  
approved computers with receptacle rated 100~240V AC, 50/60Hz,  
1.0A (minimum) only.  
5. Environment  
Place the monitor on a flat and leveled surface.  
Place the monitor in a well-ventilated place.  
Keep the monitor away from:  
Overly hot, cold or humid places, places directly under sunlight,  
dusty surroundings, equipment that generate strong magnetic fields.  
Please adjust the frequency to 60 Hz after setting up the LCD monitor.  
Then push the OSD menu button and use the auto adjust function to find  
the best mode of your computer.  
5
 
2. Control Functions  
The monitor digital control functions are located on the front panel. They are  
shown in the figure below and described in the following paragraphs.  
1. Power switch with indicator LED  
2. Function Keys  
Function Selection  
1. Press the 1knob to show the OSD menu. Then use the and ”  
knobs to select a function. Press the 2knob to close the OSD menu.  
2. With the and knobs, you can adjust the speaker volume on the  
monitor.  
When you press the knob, the speakers are mute. Press the ”  
knob one more time. The speakers are active.  
When you press the knob, the speaker volume OSD is shown.  
You can increase or decrease the volume by pressing the and  
knobs.  
3. You can hold the 2knob for more than 3 second to adjust the image  
quality automatically.  
The OSD menu will close automatically after 3-10 seconds without operation  
and saves any changes you have made.  
Function Adjustments  
1. Signal Select  
VGA  
DVI  
Exit  
- Select the image signal coming from the VGA cable.  
- Select the image signal coming from the DVI cable. (optional)  
- Close the Signal Select OSD menu.  
6
 
2. Video  
Brightness  
- Adjust the luminance level of the image.  
- Adjust the contrast level of the image.  
Contrast  
Black Level - Adjust the black Level of the image.  
Exit  
- Close the Video OSD menu.  
3. Audio  
Volume  
- Adjust the speaker volume  
Balance  
Exit  
- Adjust the speaker volume to right side or left side.  
- Exit the Audio OSD menu.  
4. Color  
Color Temperature  
User  
- Adjust the R.G.B. gain level.  
6500K  
- Select color temperature of 6500°K.  
- Select color temperature of 9300°K.  
- Close the Color Temperature OSD menu.  
- Adjust the flesh tone of the image.  
- Adjust the shade of the image color.  
- Adjust the saturation of the image color.  
- Close the Color OSD menu.  
9300K  
Exit  
Flesh Tone  
Hue  
Saturation  
Exit  
5. Image  
Auto Tune  
H. Width  
H. Phase  
H. Position  
V. Position  
Exit  
- Adjust geometry of the image automatically.  
- Adjust the horizontal sync size of signal.  
- Adjust the horizontal sync phase of signal.  
- Adjust the horizontal position of the image.  
- Adjust the vertical position of the image.  
- Close the Image OSD menu.  
7
 
6. Language  
- Set the language of the OSD windows.  
- Setting the OSD menu display time.  
7. Tools  
OSD Control  
OSD Timer  
OSD H. Position - Adjust the horizontal position of the OSD menu.  
OSD V. Position - Adjust the vertical position of the OSD menu.  
Exit  
Recall  
- Close the OSD Control OSD menu.  
- Recall the factory default setting.  
- Adjust the picture more clearly.  
- Close the Tools OSD menu.  
Sharpness  
Exit  
8. Exit  
- Close the OSD menu.  
3. Installation  
Unpacking  
Open the shipping carton and check the package contents.  
If any items are missing or damaged, contact us immediately.  
The package should include the following items:  
-14TFT-LCD monitor  
-Power cord  
-AC/DC power adapter  
-VGA cable  
-Audio cable  
-User's manual  
8
 
Follow these steps to install the base:  
1. Turn the monitor down.  
2. Assembly the base to the arm with screw.  
3. Tighten the screw with a coin.  
Installing the Monitor  
This monitor is equipped with an auto sensing DC power adapter for voltage  
ranges of 100-240VAC, 60/50Hz. Follow these steps to install the monitor:  
1.Before you connect the cables, made sure that the monitor and the system  
unit power switches are off.  
2.Plug one end of the 15 pin-signal cable to the monitor and the other end to  
the video signal connector at the rear of the system. Tighten the two screws  
on the cable connector.  
3.Connect the AC/DC power cord to the DC jack.  
4.Connect the power cable.  
4. Display Modes  
Micro-controller Features  
The micro-controller automatically detects the video board installed in your  
system. When you turn on the monitor, the micro-controller checks the  
display mode memory stored in the user setting area of the video board, and  
then the factory presetting area. It then adjusts to the proper display mode.  
The micro-controller has the memory capacity to store different display  
modes, including timing formats and display-settings. This memory capacity  
is divided into two parts: the user setting area and the factory presetting area.  
9
 
User Setting Area  
The user settings by the user on the last display mode maintain in the memory  
of the micro-controller. You can change the settings or add a nonstandard mode.  
The micro-controller always detects and displays the last mode stored in the user  
setting area when the monitor is turned on.  
Factory Presetting Area  
There are some preferred display modes preset in the micro-controller. These  
display modes are preset at the factory and include the most popular display  
modes currently available. The micro-controller searches for a proper display  
mode in this area if it fails to find a proper display mode in the user setting  
area.  
MODE  
Resolution  
Horizontal  
Vertical  
Remark  
(Dots*lines) Freq.(KHz) Freq.(Hz)  
1.  
2.  
3.  
VGA  
640×480  
800×600  
1024×768  
31.5  
37.9  
48.4  
60  
60  
60  
Non-interlaced  
Non-interlaced  
Non-interlaced  
VESA/60  
VESA/60  
5. Signal Connector Pin-outs  
To connect VGA, 8514A or IBM-compatible graphics adapters, use a 15 pin  
mini D-type male connector.  
10  
 
15-pin Mini D-type Male Connector  
Pin Assignment  
1
2
3
4
5
Red Video  
Green Video  
Blue Video  
Ground  
6
7
8
9
Red Ground  
11 Ground  
12 Serial Data/I/O  
13 H. Sync  
14 V. Sync  
15 Serial Clock Input  
Green Ground  
Blue Ground  
No Connection  
No Connection  
10 Sync Ground  
6. Power Saving Features  
When the power saving is active, the power indicator LED will be from Green  
Light to Amber. The power saving feature complies with these VESA power  
saving modes:  
Power  
Consumption  
Mode  
H. Sync. V. Sync. LED  
Normal  
Stand-by  
Suspend  
Off  
On  
Off  
On  
Off  
On  
On  
Off  
Off  
Green  
Amber  
Amber  
Amber  
<30W  
< 3W  
< 3W  
< 3W  
The monitor uses the H. Sync and V. Sync signals to determine the operation  
mode to enter.  
The monitor power-saving feature automatically turns off H. Sync and V. Sync if  
there is no input from the system for a certain period of time. To use this feature,  
you need a green PC that is compliant with the VESA power saving feature or a  
software utility to detect system input such as keyboard or mouse.  
Time Settings  
Time settings are adjusted from the system unit by software. To fulfill the  
requirements in the NUTEK specification 803299/94 the total time from  
indicated inactivity to Power Saving position A2 (VESA OFF) must not be  
set more than 70 minutes. We recommend you switch off the monitor when  
you do not intend to use it for a while.  
11  
 
7. Product Specifications  
Model  
V141  
Features  
Panel Type:  
Size:  
Anti-glare, active TFT-LCD  
14.1diagonal  
Pixel Pitch:  
Brightness:  
0.279 (W) ×0.279 (H) mm  
150 cd/(typical)  
300:1 (typical)  
23 ms (typical)  
80° / 50°  
Contrast Ratio:  
Response Time:  
Viewing Angle(H / V)  
Max. Resolution:  
Display Color  
1024 (W) x 768 (H) @ 60 Hz (non-interlace)  
262K  
Maximum Viewable Size  
Video Input  
14.1 inch (35.8cm)  
Analog:15-pin, D-sub connector  
Display Area  
11.2 (W) x 8.4 (H) inch  
[286(W) x 214 (H) mm]  
Power Supply  
Input voltage:  
100-240V /60-50Hz  
Output rating:  
12V DC, 3.0A  
Power Consumption  
25 watts (maximum), 3 watts (standby)  
Audio  
2 watts x 2 built-in speakers  
Horizontal:30-48KHz; Vertical: 50-60Hz  
13.8(W) x 13.6(H) x 5.5(D) inch  
[ 350(W) x 345(H) x 140(D) mm]  
UL, CUL, FCC-B, CE, TUV/GS  
N.W.: 6.7 lbs (3.0Kgs)  
Frequency  
Dimensions(set size)  
Safety & EMI  
Weight  
G.W.: 7.9 lbs (3.6Kgs)  
Operating Conditions  
Storage Conditions:  
5°C 35°C; 20%-80% RH  
-20°C 60°C; 10%-90% RH  
12  
 
8. Dead Pixel Policy  
Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra  
guarantees that the monitor will be replaced if the number of dead pixels on  
our monitor exceeds 5 pixels.  
9. Warranty & Customer Service  
Warranty  
ViewEra warrants the V141 TFT-LCD monitor for three years for parts and  
labor, one year for LCD panel from the date of purchase. For detail warranty  
information,  
please  
refer  
to  
our  
website  
Customer Service  
Contact your ViewEra retailer or ViewEra for after sale service.  
You may contact ViewEra Customer Support as below:  
1. By Mail: 328 Paseo Tesoro, Walnut, CA 91789  
2. By Telephone: (909)595-3748  
3. By Fax: (909)595-3526  
4. By E-mail: [email protected]  
The business hours are 9:00 am 6:00 pm PST, Mon Fri.  
13  
 
10. Windows setup  
For the best view, please set the monitor type in Windows.  
Please select as follows :  
Control Panel > Monitor > Setting > Advance > Monitor > Change > Show all  
List > Stand >  
For 1024 ×768, please set to XGA 1024 × 768 @ 60Hz”  
14  
 
11. Trouble Shooting  
1) Power on but no picture  
Make sure the VGA cable is tightly connected from the video output connector  
on the video card to the video input connector on the monitor.  
Make sure you are using the standard power adapter coming with the monitor.  
Check your video card if the driver is correctly installed. If there is no video  
signal from the video card, NO INPUT SIGNALwill show on the screen.  
2) Wrong or abnormal colors  
If any color (red, green, or blue) is missing, check video cable to make sure it is  
securely connected. Loose pins in the cable connector can cause a bad  
connection.  
3) The text and icon look blurry  
LCD monitor has a native resolution which pixels are produced by cells in  
fixed positions. When a resolution different from the native resolution is  
chosen, the LCD monitor uses various interpolation methods to achieve the  
pseudo resolution. To achieve the optimum viewing quality, choose the native  
resolution of the panel is recommended.  
Use Auto Tuningfunction to adjust image quality on the OSD menu or you  
can hold button 2 for 3 seconds to do auto tuning.  
4) Display position is incorrect  
Use Auto Tuningfunction to adjust image position on the OSD menu or you  
can hold button 2 for 3 seconds to do auto tuning.  
5) Speakers have no sound  
Make sure the audio cable is tightly connected from the audio output jack on  
the PC to the audio input jack on the monitor.  
15  
 
6) Residue image  
If an image remains on the screen for an extended period of time, it may be  
imprinted in the screen and leave a residue image. It is characteristic of liquid  
crystal and is not malfunction or deterioration of the liquid crystal. The residue  
image will disappear after a period of time. It is recommended to set up the  
screen saver for your LCD monitor.  
16  
 

Tascam Personal Computer US 144 User Manual
Toastmaster Convection Oven RM 5T User Manual
Toshiba Digital Camera PDR M4 User Manual
Toshiba Projector TDP SW80 User Manual
True Manufacturing Company Refrigerator TMW 36F User Manual
Tyco Electronics Radio MM102014V1 User Manual
Tyler Refrigeration Thermostat NSSD User Manual
Vulcan Hart Fondue Maker ICM24 ML 52470 52476 ICM36 ML 52471 52477 ICM48 ML 52472 52478 ICM60 ML 5274352479 ICM72 ML 52474 52480 User Manual
Wayne Dalton Garage Door Opener Wireless Wall Station User Manual
Weber Oven 178760 User Manual